Industrial Equipment Vibration and Temperature Monitoring
A power generation monitoring architecture for pipeline vibration, valve system vibration, turbine pipeline health, condenser pipeline condition, and high-temperature sensor deployment.
Project Type
Industrial Equipment Monitoring
System Scale
heating extraction steam valves, high-pressure exhaust pipelines, heat-exchange extraction pipelines, turbine pipelines, condenser pipelines, and distributed temperature and vibration points
Data Output
pipeline vibration, valve vibration, turbine pipeline vibration, condenser pipeline vibration, pipeline temperature, scheduled status data
Engineering Value
How the system supported engineering decisions
The case converts power generation valve, pipeline, turbine, and condenser monitoring into one public DL-SHM workflow.
High-temperature DL-SEN vibration and temperature points are mapped to DL-DAQ acquisition and DL-SHM alarm management.
The monitoring scope supports early abnormal-condition detection for heating and turbine pipeline equipment.
Monitoring Content
Monitoring scope and field constraints addressed by the deployment
High-temperature valve and steam pipeline zones required stable vibration capture without exposing sensors to thermal interference.
Permanent turbine and condenser pipeline monitoring required long-term synchronized acquisition and health alarm management.
Pipeline temperature and vibration points required periodic remote acquisition and transmission to a monitoring center.
System Configuration
Configured system architecture and data path
Field Devices
DL-SEN high-temperature acceleration, temperature, and industrial vibration sensors installed on valves, steam pipelines, turbine pipelines, condenser pipelines, and heating pipeline sections
Communication Layer
Synchronized wired acquisition and remote scheduled transmission from field points to DL-DAQ systems
Central Platform
DL-SHM monitoring systems for vibration trend display, pipeline status review, alarm management, data storage, and engineering reporting
Sensor Deployment
Sensor layout and measurement purpose
Heating extraction steam valves and high-pressure exhaust pipelines
DL-SEN high-temperature acceleration sensors
Capture valve and pipeline vibration to identify abnormal operating response
Turbine and condenser pipeline sections
DL-SEN high-temperature and low-temperature vibration sensors
Monitor turbine load influence on pipeline vibration under permanent health monitoring conditions
Distributed heating pipeline points
DL-SEN temperature and piezoelectric acceleration sensors
Collect pipeline temperature and vibration records at multiple locations
Monitoring center
DL-DAQ systems and DL-SHM monitoring systems
Provide scheduled acquisition, data transmission, real-time trend review, intelligent alarms, and engineering reports
Data Analysis Results
Monitoring indicators and interpretation
Pipeline and valve vibration
high-temperature vibration records
Operators could observe vibration behavior around steam valves and key pipeline sections.
Turbine pipeline health
permanent vibration monitoring dataset
Turbine load influence on pipeline condition could be reviewed through long-term data.
Remote pipeline status
scheduled temperature and vibration acquisition
Distributed monitoring points supported remote status review from the monitoring center.
Engineering Credibility
Reliability, topology, and project validation
99.98%
target data availability
IP67/68
field protection classes
4G/Fiber
site transmission options
RFQ
project-based configuration
Measurement planning
Monitoring object, measurement range, sampling rate, and signal type guide project configuration.
Communication options
DL systems support project configurations using wired, wireless, GNSS, and gateway-based communication methods.
Documentation support
Datasheets and technical selection information are available upon request for RFQ preparation.
Product selection should be confirmed against site conditions, measurement points, installation environment, and expected data output.
Structured RFQ Path
Request path for Industrial Equipment Monitoring Project
Step 1
Define Data Nodes
Sensor, wireless node, GNSS station, seismic unit, or DAQ field layer.
Step 2
Configure Network
Civil infrastructure, industrial equipment, heritage, seismic, or research monitoring chain.
Step 3
Build RFQ Scope
Asset type, measurement points, channels, sampling rate, communication, environment, and duration.
Step 4
Review Proposal
Receive system architecture, product configuration, data output, and engineering review structure.
Project Overview
Engineering context and monitoring scope
Haiyang power generation projects required vibration monitoring on Unit 1 heating supply pipelines and valves, permanent health monitoring for turbine and condenser pipelines, and online monitoring of heating pipeline temperature and vibration. The source deck describes high-temperature acceleration sensors installed on heating extraction steam regulating valves, high-pressure exhaust pipelines, heat-exchange extraction pipelines, turbine pipelines, and distributed pipeline locations.
Client type
Power generation turbine island and heating pipeline operation teams
System scale
heating extraction steam valves, high-pressure exhaust pipelines, heat-exchange extraction pipelines, turbine pipelines, condenser pipelines, and distributed temperature and vibration points
Project type
Industrial Equipment Monitoring